Bw-trailer-hitches Turnoverball Model 1384 (Dodge) Bedienungsanleitung PDF herunterladen (Seite 4)

Install the center section. With the latch pin

mechanism on the drivers side, raise the center

section into place as shown, see figure B5. In order to

clear structures under the truck bed, the center will

have to be lifted into place on an angle over the

exhaust, then positioned directly under the frame

cross member so that the raised portion of the center

can be pushed straight up through the hole in the

frame cross member, and through the hole in the

plastic spacer block. Having assistance in the bed to

guide the top of the center section is recommended.

Line the 4 holes in the center section up with the

frame holes and the holes in the threaded blocks.

Thread a 5/8 flange head bolt into each hole.

Square the hitch. Using a tape measure, be sure that

the full length of the gooseneck hitch is centered

within the channel of the frame cross member. Do this

by making sure that the gap between the center

section and the frame cross member is the same on

the driver and passenger sides. The hitch must not be

touching the brake lines that are anchored to the

frame cross member.

Tighten the 5/8" bolts. With the hitch square and

firmly pressed against the frame cross member,

tighten the 5/8" bolts. To better access the bolts on the

passenger side of the center section the exhaust may

be lowerd to allow access to the bolts, see preparing

to install section step 7. Torque the bolts to 100 ft. lbs.

SECURE HITCH

Disengage lifting device.

If a lifting device was

used to hold the center section in place during

the installation, remove it at this time

INSTALL LATCH PIN HANDLE

Install bolts. Retract the latching mechanism by

pulling on the tab with the square holes and pushing it

toward the cab. From the top down, insert a 3/8

carriage bolt in each of the square holes in the

latching mechanism, see figure D1.

Serious injury can occur due to the pinch point

located at the intersection of the latching

mechanism and the center section.

Install the latch pin handle.

Beginning under the

vehicle "thread" the end of the handle with the vinyl

grip in front of the brake lines and over the frame on

the drivers side. Attach the handle to the latching

mechanism over the 3/8 carriage bolts with two 3/8

locking flange nuts, see figure D2. Be sure that the

handle is in the proper position and that it does not

interfere with any other components of the vehicle.

Torque the nuts to 30 ft. lbs. to secure the handle.

Notice: The latch handle must be positioned on the

"cab side" of the brake lines directly over the axle.

Install safety chain bracket.

With the Center section

loosely attached to the truck frame, locate and install

the safety chain bracket by inserting the flange of the

bracket with four holes between the bed crossmember

and the frame crossmember and pushing up against

the truckbed. Attach the safety chain bracket to the

center section with three 1/2" x 1−1/2" bolts, 1/2" lock

washers, and 1/2" nuts, as shown in figure C1. Do not

fully tighten at this time.

Tighten the Safety chain bracket bolts.

Tighten the

three 1/2" bolts attaching the safety chain bracket to

the center section. Torque the bolts to 80 ft. lbs.

Figure B5: Looking up at the bed from foward of driver side tire.

FIGURE D1: Looking up at center section

FIGURE D2: Looking back at driver side of center section.

FIGURE C1: View looking up at center from under the truckbed.

SAFETY CHAIN

BRACKET

BED CROSSMEMBER

FRAME

CROSSMEMBER

FRAME

CROSSMEMBER

EXHAUST

CENTER

SECTIONS

CENTER

SECTION

LATCHING

MECHANISM TAB

LATCH PIN HANDLE

FRAME

1 2 3 4 5

Kommentare zu diesen Handbüchern

Keine Kommentare

Bw-trailer-hitches Turnoverball Model 1384 (Dodge) Bedienungsanleitung Seite 4

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Bw-trailer-hitches Turnoverball Model 1384 (Dodge)